{"product_id":"style-flare-kit-suit-2024-2025-isuzu-d-max","title":"OFF-ROAD STYLE FLARE KIT Suit 2024\/2026 Isuzu D-MAX","description":"\u003cp\u003e\u003cstrong\u003eCOMPATIBLE With- 2024\/2026 Isuzu D-MAX\u003c\/strong\u003e\u003cbr\u003e(\u003cstrong\u003eApproximately 40-50 mm\u003c\/strong\u003e additional poke coverage.)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMatte Black colour only\u003c\/strong\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"text-decoration: underline;\"\u003e\u003cstrong\u003eFender Flare Kit Installation Guide\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eGeneral Instructions for Front and Rear Fender Flares Suited for Various Vehicle Models\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e1. Initial Test Fit:\u003c\/strong\u003e\u003cbr\u003eBefore you begin installation, always perform a full test fit of all flare components. This step helps you understand the fitting process, check for any issues, and ensure you're comfortable with the placement. It might take a bit more time, but it’s worth doing properly.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e2. Rear Flares:\u003c\/strong\u003e\u003cbr\u003eStart with the rear flares. Remove the mud flap screws and take off the rear mud flaps. Position the flare onto the guard and loosely fit it using the mud flap screws, along with the additional screws that line up near the rear of the cabin.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNote: \u003c\/strong\u003eOur flare kits are compatible with all standard mud flaps. You can refit the original mud flaps using the same screws once the flares are mounted.\u003c\/p\u003e\n\u003cp\u003eCheck the flare alignment and make sure it sits flush. Repeat the same on the opposite side.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3. Front Flares:\u003c\/strong\u003e\u003cbr\u003eMove to the front flares. Again, remove the mud flap screws and mud flaps. Position the flare onto the guard using the same mounting points. If your vehicle has a snorkel—especially large footprint snorkels like Safari—check for clearance, as trimming may be required.\u003c\/p\u003e\n\u003cp\u003eRefit the standard front mud flaps using the original screws once the flare is in place.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e4. Front Bumper Section (If Applicable):\u003c\/strong\u003e\u003cbr\u003eIf your vehicle does not have a bull bar and still retains the front bumper, your flare kit may include two small bumper flare sections. These require drilling.\u003c\/p\u003e\n\u003cp\u003eFit the rear section of the front flare first, then hold the bumper flare in place. You’ll see where holes need to be marked and drilled. Once marked, drill holes as required and secure using the provided clips and screws.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e5. Cleaning Before Final Fitment:\u003c\/strong\u003e\u003cbr\u003eAfter the test fit and before final install, clean all contact surfaces. \u003cspan style=\"text-decoration: underline;\"\u003e\u003cstrong\u003eUse a 50-50 mix of isopropyl alcohol and water to wipe down the guards\u003c\/strong\u003e\u003c\/span\u003e or panels where the adhesive will bond.\u003c\/p\u003e\n\u003cp\u003eThis removes dirt, road grime, bug matter, and any other contaminants that could prevent proper adhesion. Allow everything to dry completely before continuing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e6. Preparing the Adhesive Tape:\u003c\/strong\u003e\u003cbr\u003eBefore screwing in the flares, prepare the adhesive tape for easy removal. The adhesive strip runs along the top edge of each flare.\u003c\/p\u003e\n\u003cp\u003ePeel back a small section of the red backing tape from both ends of each flare piece. Let the ends hang loose so you can grab them later. This way, once the flare is screwed in and sitting where it should, you can pull the tape out smoothly. If one side snaps off, you’ll have the other end as a backup to pull from.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e7. Final Fit and Bonding:\u003c\/strong\u003e\u003cbr\u003eWith the flare screwed in and adhesive tape backing removed, use a clean microfiber or soft cloth to press along the top edge of the flare. Apply firm, even pressure across the full length to activate the adhesive and ensure it bonds properly.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant – Curing Time:\u003c\/strong\u003e\u003cbr\u003eDo not expose the adhesive to any water or moisture for at least twenty-four hours after installation. This includes rain, washing the vehicle, or any kind of damp conditions. Allowing full curing time will help the adhesive achieve maximum bond strength and prevent lifting or failure.\u003c\/p\u003e","brand":"R\u0026R Products And Supplies","offers":[{"title":"Default Title","offer_id":44117041184948,"sku":null,"price":600.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0255\/1293\/5514\/files\/rn-image_picker_lib_temp_99313efa-1d95-432c-9154-bfe19f1e9194.jpg?v=1767473830","url":"https:\/\/www.rrproductsandsupplies.com.au\/products\/style-flare-kit-suit-2024-2025-isuzu-d-max","provider":"R\u0026R Products And Supplies","version":"1.0","type":"link"}